Delamu 128in Cord Hider for 1 Cord, Self-Adhesive Cord Covers
Quick take
The Delamu CC05 one-cord wall cord hider is a slim, paintable raceway made to conceal a single mini cord (about 0.23 in, 5.8 mm diameter). It sticks to the wall with self-adhesive mounting for fast, connector-free install, but it is not meant for thicker cables, and it is not designed for Cat5 or Cat6 network wiring.
Pros and cons
Pros
- Slim, rounded profile that is intended to be subtle on walls (and is paintable and cuttable).
- Self-adhesive installation, designed to avoid wall drilling for many setups.
- No connectors needed for straightforward installs, designed for quick runs around common home cable paths.
- Built for safety-focused use cases, including a UL94 V-0 flammability test claim.
Cons
- Designed for one mini cord only, so it will not fit larger cables.
- Adhesion is not recommended for textured walls.
- It is not intended for Ethernet (Cat5/Cat6).
What buyers think
Buyer-review evidence points to a consistent theme: this cord hider is most satisfying when the cable size is a close match and the install line is measured before sticking. Many reports highlight that it blends in visually, stays neat, and feels easy to work with (including trimming to size). Installers also tend to stress careful placement because the adhesive tape can be very strong once applied. Review evidence also suggests the pieces are commonly segmented into shorter lengths, so lining up sections matters for the cleanest look. Overall, buyer feedback supports that the product delivers tidy, wall-level cord management when used for its intended one-cord, mini-cable purpose, with limited usefulness outside that fit.
What this cord hider is for
This is a single-cord cable raceway designed to hide one low-visibility cable run where you want the wiring to stay off the wall surface. It is aimed at common home and office cords such as lamp cable, speaker cable, ultra-thin TV or monitor power connections, and similar mini cables. The enclosure is built from PVC, and it is sized to work with a mini single standard cord around 0.23 in (5.8 mm) diameter.
Fit and cable size limitations (important)
The biggest deciding factor is whether your cord matches the intended “one mini cord” size. If your cable is thicker than the raceway expects, it will not close cleanly or will look misaligned. It is also specifically not intended for Cat5 or Cat6 network cable.
If you are unsure, measure your cable diameter at the thickest point (including any outer jacket ridge) and compare it to the intended mini-cord target size of about 0.23 in (5.8 mm). This cord hider is a good fit for “one cord only” scenarios, not cable bundles.
Installation: peel-and-stick with careful placement
The design uses a self-adhesive mounting approach and is connector-free, which is meant to simplify installs. The general flow is to peel and stick the tape on the back of the channel, press it to the wall, place the cord into the raceway, then close the cover. This can be attractive if you do not want screws and anchors or you are trying to keep installation time short.
Multiple buyer reports emphasize that adhesion can be very strong, so you want to line up the run before committing. Some buyers also mention trimming the channel to size with common cutting tools. If your wall is textured, adhesion is not recommended, so you may need a different mounting approach or a different product style.
Appearance and finishing options
The raceway is described as paintable and cuttable, with a slender, round-arc profile that is intended to look more like part of the wall than a bulky conduit. If you are matching a room’s color scheme, paintability can help the raceway disappear visually. The white color is intended as a baseline option, and the cuttable form makes it easier to tailor shorter sections to your layout.
Safety and material considerations
This product includes a UL94 V-0 flammability test claim. For buyers, the practical takeaway is that the enclosure material is designed to be more flame-retardant than ordinary plastics, supporting a safer everyday setup where cords would otherwise be exposed, including areas where pets or children can access cables.
Who should buy this, and who should skip it
Best for
- People who need to conceal one mini cord (around 0.23 in diameter) along a wall, baseboard, or simple TV-area path.
- Shoppers who prefer tool-free, adhesive-based cord management.
- Anyone wanting a slim, paintable raceway that looks understated.
Skip it if
- You need to run multiple cables in one channel, or your cord is thicker than a mini single cable.
- Your installation surface is textured, where adhesive bonding may be less reliable.
- You are trying to hide Cat5 or Cat6 Ethernet cable.
Alternatives to consider (by the real decision criteria)
- For multiple cables: Look for multi-cable or wider raceway kits, where you do not have to choose between cable fit and a clean closure.
- For Ethernet networking: Choose cord management designed or sized for Ethernet runs rather than a mini cord-only channel.
- For textured walls: Consider mounting options that do not rely on adhesive tape alone, or use a raceway system that supports other attachment methods.
Verdict
The Delamu CC05 one-cord wall cord hider is a strong choice when you have a single ultra-thin cord to hide and you want a clean, paintable, low-profile look. The main tradeoff is strict sizing and cable-type suitability, so double-check your cable diameter and skip it for Ethernet or thicker wires. If your use case matches, buyer feedback suggests it delivers a noticeably neater setup with straightforward installation.
FAQ
Is this cord hider only for one cable?
Yes. It is designed to manage a single mini cord (about 0.23 in, 5.8 mm diameter). It is not intended for multiple cables or larger cords.
Will it fit Ethernet cables like Cat5 or Cat6?
No. It is not designed to be used for Cat5 or Cat6 network cable.
How does installation work?
It uses self-adhesive mounting and a connector-free channel design. You peel and stick the tape to the back of the raceway, press it to the wall, insert the cord, then close the cover.
Can I use it on textured walls?
Adhesive installation is not recommended for textured walls.
Is the cord cover paintable?
Yes. It is described as paintable and cuttable, which can help it blend into different wall colors.
How do I cut it to fit?
It is cuttable, and buyers report using common tools to trim it to the length you need.
Specifications
| Product Title | Delamu 128in Cord Hider for 1 Cord, Self-Adhesive Cord Covers for Wires on Wall, Easier Install Wire Covers for Cords on Wall, Cable Wire Hider, Cable Cover Management Raceway, W0.48 H0.3in, White |
|---|---|
| Category | Electronics > Accessories & Supplies > Cord Management > Cable Raceways |
| Brand | Delamu |
| Manufacturer | Delamu |
| Model Number | CC05 |
| Color | White |
| Material | Polyvinyl Chloride |
| Product Dimensions | 14.2"L x 0.48"W |
| Indoor Outdoor Usage | Indoor |
| Number of Pieces | 1 |
| UPC | 619660477710 |
| Unit Count | 11.83 Feet |
| Mfr Part Number | CC05 |
| Warranty Description | NoWarningApplicable |
| Enclosure Material | Polyvinyl Chloride |
| Item Dimensions L x W | 14.2"L x 0.48"W |
| Installation Type | Self-Adhesive |
| Style Name | Cord Hider |
| Style | Cord Hider |
Available variants
Size
- 236in L X 1.18in W X 0.63in H
- 142in L X 0.94in W X 0.47in H
- 142in L X 1.18in W X 0.63in H
- 128in L X 0.48in W X 0.30in H
- 236in L X 0.94in W X 0.47in H
Color
- White
- Black
- Beige
- Grey
Recommended next
Mount-It! in-Wall TV Cable Concealer Kit with Recessed Power – Triple Outlet, 9ft Cord, and Hand Saw
The Mount-It! in-wall TV cable concealer kit is a plug-in (not hard-wired) way to hide TV, soundbar, and media cables, while keeping power connections neatly contained. It includes a drywall saw, cutting template, and mounting plates, with an easy DIY-focused approach, but you must confirm wall cavity depth and stud layout before cutting.
Delamu Cord Hider, 157in Wire Covers for Cords on Wall
The Delamu Cord Hider (157-inch wall-mounted cable raceway) is designed to conceal 2 to 3 cords in a clean, paintable channel. It installs with an attach-and-snap design and can use adhesive tape or screws, but the adhesive tape is strong enough to risk paint damage if you remove it later.
Cord Cover Wall 32in, TV Cord Hider for Wall Mounted review
The ZhiYo cord cover kit is a snap-on wall wire raceway designed to hide multiple TV cables without drilling. It’s built for a clean, minimal look, uses a PVC channel rated UL94 V-0, and includes two 15.8-inch sections for about 31.5 inches total. Biggest tradeoff: adhesive-only installation can make removal hard and may mark drywall.
630in Cord Hider Kit, Paintable Cable Raceway, Cord Covers for Wires on Wall (YesBes)
A long, connector-rich cord hider kit designed to make wall-mounted TV setups look cleaner fast. It uses self-adhesive installation (no drilling), snaps shut to conceal 2 to 4 cords, and can be cut and painted to match your wall.