10GBASE-T SFP+ to RJ45 Transceiver, 1/2.5/5/10G Multi-Rate Copper SFP+ to Ethernet Module
Quick take
This multi-rate 10GBASE-T SFP+ to RJ45 transceiver converts an SFP+ copper-capable port into a standard RJ45 Ethernet connection. It targets buyers who want higher speeds over existing CAT6a or CAT7 runs (up to 30m) without pulling new fiber.
The main caveat from real-world feedback is reliability variance in the field. Some setups run smoothly, while a subset of users report early module failures, making cooling and deployment conditions worth considering.
Pros and cons
Pros
- Multi-rate auto-negotiation for 1G/2.5G/5G/10G over copper
- RJ45 solution for SFP+ cages, designed for fiber-to-Ethernet style upgrades
- Hot-pluggable SFP+ behavior for easier swapping (no full reboot required)
- Supports CAT6a/CAT7 cabling up to 30m
Cons
- Buyer reports are mixed on long-term stability, including instances of early failure
- Not compatible with HP/HPE switches (important if you are in that ecosystem)
- Performance will depend on your switch’s exact SFP+ port behavior and your cabling quality
What buyers think
Buyer-review evidence points to two recurring themes: compatibility and link behavior, plus a reliability split.
On the positive side, several buyers describe straightforward setup and successful use in environments that use SFP+ jacks, including Unifi deployments. Others specifically mention that the module can help achieve multigig or targeted negotiation behavior on certain UDM Pro-style configurations, rather than limiting the link to 1G.
On the negative side, the review evidence is limited but includes reports of modules failing relatively soon (for example, after a few days or within a few months). In one case, additional cooling was mentioned as part of a fix after an initial failure, suggesting that deployment conditions may matter for some units.
Because the negative outcomes are not universal across all reviewers, overall confidence is best when you ensure compatibility, use good copper cabling, and provide adequate airflow in your rack.
How this 10GBASE-T SFP+ to RJ45 transceiver fits real networks
This is an SFP+ form-factor transceiver that gives you an RJ45 port on the far end. That matters when your switch has SFP+ slots but you want Ethernet over copper instead of fiber.
It’s designed around multi-rate Ethernet, so it can negotiate down to match what your network supports (1G, 2.5G, 5G, or 10G). If your goal is upgrading backhaul or LAN segments over existing CAT6a or CAT7, that auto-negotiation is a practical advantage.
Key specs that influence performance
Supported speeds and negotiation
The module supports 1G/2.5G/5G/10G auto-negotiation. In practice, your negotiated speed depends on both sides of the link, especially the switch’s SFP+ port capabilities and configuration.
Cable type and distance
For copper, it is intended to link using CAT6a or CAT7 cabling, up to 30m. If you are planning longer runs, tighter tolerances, or mixed cable types, it increases the risk of negotiating lower speeds.
Hardware format and materials
It uses an SFP+ to RJ45 interface, built with an aluminum case. It’s a single-port module.
Compatibility: which switches and environments to double-check
Compatibility is a major decision factor for SFP+ transceivers, and this one is marketed for open SFP transceiver environments.
It’s listed as compatible with devices such as Cisco SFP-10G-T-S, Ubiquiti UniFi UF-RJ45-10G, Meraki MA-SFP-10GB-T, Mikrotik S+RJ10, Netgear AXM765, and other open SFP transceiver setups.
Important: it is not compatible with HP/HPE switches.
Pros and cons from an everyday buyer perspective
Pros if you’re upgrading copper without new fiber
- Cleaner retrofit: You keep RJ45 wiring in place while leveraging a switch’s SFP+ cage.
- Multi-rate links: Negotiation can help you land on the highest stable speed both ends can support.
- Hot-plug swapping: If you need to replace modules or reconfigure ports, hot-plug behavior can reduce downtime.
Cons to weigh before buying
- Mixed reliability signals: Some buyers report successful operation for months, while others report early failures. If you’re buying multiple modules, this makes it especially important to plan for airflow and a careful first test in your rack.
- Speed depends on the environment: Cable quality, length, and the switch’s SFP+ negotiation behavior all affect the outcome. Expect negotiation to match real-world conditions, not just the advertised maximum.
- Not for HP/HPE: If you use HP/HPE switching, you will need a different module type or vendor-compatible option.
Verdict: is it worth it?
Buy this if you have a switch with compatible SFP+ cages, you need an RJ45 copper port, and your CAT6a/CAT7 runs are within the intended distance range. It’s a strong fit for home and small business backhaul or LAN upgrades where fiber is inconvenient.
Consider alternatives or verify carefully if you are using HP/HPE switches, you cannot ensure solid cooling in a tightly packed rack, or you need guaranteed long-term stability for mission-critical production links. In that case, it’s smart to compare module options with more consistent field reliability signals for your specific switch model and airflow setup.
How to choose the right speed (and avoid surprises)
- Match the cable plan: Use CAT6a/CAT7 and keep within the stated 30m target when possible.
- Validate negotiation on your switch: Some platforms negotiate differently based on firmware and port behavior. Plan to test at the desired speed.
- Think about rack airflow: Cooling came up in user experiences around stability. If your rack is warm or port density is high, prioritize airflow around the switch.
FAQ
What speeds does this 10GBASE-T SFP+ to RJ45 transceiver support?
It supports multi-rate auto-negotiation for 1G, 2.5G, 5G, and 10G.
How far can I run CAT6a or CAT7 with this module?
It’s intended for CAT6a/CAT7 copper links up to 30m.
Is it plug and play?
It’s described as hot-pluggable, meaning you can insert the module without shutting down the network or rebooting the device.
Which switches is it compatible with, and who should avoid it?
It’s marketed for open SFP transceiver environments and lists compatibility with several brands and models (including Cisco SFP-10G-T-S, Ubiquiti UniFi UF-RJ45-10G, Meraki, Mikrotik, Netgear, and others). It is not compatible with HP/HPE switches.
Will I definitely get 10Gbps?
Not necessarily. The link negotiates based on your switch’s SFP+ behavior and your copper cabling conditions (type, length, and overall quality).
Where can I check the latest price and availability?
Use the button below to view the most current pricing details on Amazon.
View latest price on Amazon: Buy on Amazon
Specifications
| Product Title | 10GBASE-T SFP+ to RJ45 Transceiver, 1/2.5/5/10G Multi-Rate Copper SFP+ to Ethernet Module for Cisco SFP-10G-T-S, Ubiquiti UniFi UF-RJ45-10G, Mikrotik S+RJ10, Meraki, Netgear, D-Link and More, 1 Pack |
|---|---|
| Category | Electronics > Computers & Accessories > Networking Products > Network Transceivers |
| Brand | XZSNET |
| Manufacturer | XZSNET |
| Model Number | XZS-SFP10G-T-RTL |
| Item Weight | 1.6 ounces |
| Color | For Cisco |
| Number of Ports | 1 |
| Compatible Devices | Cisco SFP-10G-T-S, Meraki MA-SFP-10GB-T, Mikrotik S+RJ10, Netgear AXM765, Supermicro, Broadcom, TP/D-Link and Other Open SFP Transceivers/Switches, Ubiquiti UniFi UF-RJ45-10G |
| Lower Temperature Rating | 32 Degrees Fahrenheit |
| Upper Temperature Rating | 158 Degrees Fahrenheit |
| Interface | SFP+ to RJ45 |
| Data Transfer Rate | 10 Bits Per Second |
| Switch Type | unmanaged |
| Platform | Not Machine Specific |
| Case Material Type | Aluminum |
| Built-In Media | 10GBASE-T SFP+ Transceiver x 1 |
| Warranty Description | 2 Year Manufacturer |
| Mfr Part Number | XZS-SFP10G-T-RTL |
| Unit Count | 1.0 Count |
| Included Components | 10GBASE-T SFP+ Transceiver x 1 |
Available variants
Capacity
- 1 Pack
- 2 Packs
Color
- For Cisco
- For Ubiquiti
Recommended next
10Gtek 10GBase-T SFP+ to RJ-45 Transceiver (CAT.6a/CAT7, up to 30m)
10Gtek’s 10GBase-T SFP+ to RJ-45 transceiver is a plug-and-play option for running 10GbE over copper using CAT.6a or better, up to about 30 meters. It’s commonly chosen for home labs and small business setups when you need flexibility with SFP+ switch ports, with strong compatibility across many mainstream networking brands (and clear exceptions).
1.25/2.5/5/10G-T SFP+ to RJ45 Transceiver, Copper Ethernet Module Compatible for review
A copper 10G SFP+ transceiver that converts an SFP+ slot to an RJ45 port, supporting speeds down to 1.25G and reaching up to 30m on Cat. 6a/7. It’s a good fit for Unifi, Mikrotik, and certain 10GbE switches, but it can run warm, so consider cooling if you’re installing it in a tight cabinet.
10Gtek 𝟭.𝟮𝟱/𝟮.𝟱/𝟱/𝟭𝟬𝗚-T SFP+ to RJ45 CAT.6a Copper Transceiver
The 10Gtek 10GBase-T SFP+ to RJ45 copper transceiver is built for switches or NICs that accept SFP+ modules and you want multi-rate Ethernet over CAT.6a/CAT7. It supports auto-negotiation across 1.25G, 2.5G, 5G, and 10G, with up to 30 meters over copper, and is aimed at compatibility with many common networking vendors. The main buying caveat is that not every brand’s switch or ecosystem supports every SFP+ copper option the same way, so double-check compatibility before buying.
A Pair of 1.25G/s Bidi Gigabit Multi-Mode Fiber Ethernet Media Converter with 2PCS Bidi SFP LC Dual Transceiver Module Included
A compact, plug-and-play pair of gigabit fiber media converters designed to bridge RJ45 copper to a multi-mode SFP fiber link (up to 550 m with the included transceivers). Buyers typically like the easy setup and day-to-day reliability, with the main caveat being that DOA units have been reported, so it is smart to test on arrival.