Raymarine Radar Cable with Raynet Connector, 5m
Quick take
This 5 meter Raymarine radar cable is built to connect compatible marine radar systems using a Raynet connector on one end. Buyers who report using it generally say it installed and worked without issues, but the main caveat is fit: you need the correct Raymarine-specific cable type and length for your setup.
Pros and cons
Pros
- Purpose-built for marine radar system connections
- 5 m length gives more routing flexibility than short leads
- Raynet connector design for Raymarine radar integration
- Connectors are male-to-male (8-pin) which simplifies like-for-like replacements
Cons
- Connector and cable type specificity means it may not work outside Raymarine radar setups
- Review evidence is limited, so broad performance conclusions are hard
What buyers think
Buyer-review evidence for this specific cable is limited, but the available feedback is consistently positive. The recurring theme is simple functionality, with reports that it “worked” and that there were no issues after installation. Because the dataset is small, there is not enough information to reliably assess long-term durability, signal behavior over time, or installation difficulty beyond “it worked.”
What this cable does (and what it does not)
The Raymarine Radar Cable with Raynet Connector is an accessory cable intended for connecting compatible Raymarine marine radar systems. It uses a Raynet connector and is specified as a digital radar cable, with an Ethernet connector type listed and a total of 8 pins. In other words, it is for radar interconnect use cases, not a general-purpose network or accessory cable.
Key specs that matter for choosing the right one
Length and routing
At 5 meters (about 16.4 feet), this cable is best suited when you need enough reach to route cleanly between the radar unit and the rest of the Raymarine radar electronics. If your install requires a shorter run, choosing the closest length can reduce slack and simplify cable management.
Connector type and compatibility
This cable is designed around Raynet connectivity for Raymarine radar systems. The connector is listed as male-to-male with 8 pins. That specificity is the biggest “buyer-fit” factor, so confirm you are matching the same connector ecosystem for your radar setup before ordering.
Indoor/outdoor use
The cable is listed for indoor and outdoor use, which is useful for common marine routing scenarios where runs may pass through mixed environments. If you are dealing with tight engine-room proximity or harsh routing paths, plan your cable path and strain relief carefully even when a cable is rated for outdoor use.
Pros and cons for real-world installs
When it is a good fit
- You need a Raymarine Raynet radar cable replacement for a 5 m run
- You want a straightforward like-for-like cable swap where connector gender and pin count matter
- Your install has indoor/outdoor routing and you want a cable intended for that environment
When you should pause before buying
- Your radar system requires a different connector standard, a different cable family, or a different length
- You are trying to use it for non-radar applications, since it is purpose-built for marine radar connections
Is the raymarine radar cable with raynet connector, 5m worth it?
If you are replacing a specific Raymarine radar interconnect cable and you can confirm the Raynet connector and 5 m length are correct, this is a sensible, job-specific choice. The limited review history supports the idea that it works as intended after installation. The main risk is not performance, it is compatibility, so verify that your current setup calls for this exact type of radar cable and run length.
How to compare alternatives (without getting the wrong cable)
When you are shopping for a different radar cable option, compare based on these factors:
- Length: match the routing distance you need, considering slack for service loops
- Connector ecosystem: confirm Raynet compatibility for Raymarine radar systems, and check connector gender and pin count
- Cable type: ensure it is the correct digital radar cable type for your radar configuration
- Environment: if your run is exposed, prioritize options rated for indoor/outdoor use
Price and availability
Pricing and stock can change quickly. If you want the most current cost for the Raymarine Radar Cable with Raynet Connector, 5m, check the latest listing.
FAQ
What is the Raynet connector used for on this radar cable?
The Raynet connector is used to join this cable to compatible Raymarine marine radar electronics, supporting the intended radar interconnect function.
Is this cable only for Raymarine radar systems?
It is intended for Raymarine marine radar system connections, and the Raynet connector design makes it a good fit primarily when your setup expects that same connector ecosystem.
How long is the cable, and will that be enough for typical marine routing?
The cable length is 5 meters. Whether it is enough depends on the distance between your radar unit and the connected radar electronics, including how you plan to route and manage slack.
Does it support indoor and outdoor installation?
It is listed for indoor and outdoor usage, which aligns with common marine installs that may involve mixed exposure along the cable path.
Does the cable need special configuration to work?
This is a purpose-built interconnect accessory, so it is generally used as a direct replacement or connection cable when the connector type and length match your setup. If compatibility is confirmed, no special configuration is typically required beyond proper installation.
Specifications
| Product Title | Raymarine Radar Cable with Raynet Connector, 5m |
|---|---|
| Category | Electronics > Car & Vehicle Electronics > Marine Electronics > Radar Systems |
| Brand | Raymarine |
| Manufacturer | Raymarine |
| Model Name | Raymarine 5M Digital Radar Cable w/RayNet Connector On One End |
| Color | Black |
| Item Weight | 2.7 Pounds |
| Connector Type | Ethernet |
| Cable Type | Raynet |
| Compatible Devices | Marine radar systems |
| Other Special Features of the Product | Not_Performance_Used |
| Compatible Phone Models | No Compatible Phone Models |
| Connector Gender | Male-to-Male |
| Number of Pins | 8 |
| Recommended Uses For Product | Marine radar system connection |
| Specification Met | Marine Industry Standards |
| Indoor Outdoor Usage | Indoor, Outdoor |
| Unit Count | 1.0 Count |
| Number of Items | 1 |
| Item Shape | As Shown |
| Brand Name | Raymarine |
| Customer Package Type | Standard Packaging |
| Model | A80227 |
| Item Length | 5 Meters |
| UPC | 723193770580 |
| Global Trade Identification Number | 00723193770580 |
| Warranty Description | Warranty |
Recommended next
Mirror Mount Bracket + Mirror Wire Cord - Escort 9500iX Redline
This mirror-mount installation bundle is built to let you power an Escort 9500iX/9500ix-style detector from your rearview mirror harness, reducing dash clutter. Buyers like the package value and generally straightforward install, but thin harness probe pins and fitment details can require extra care, especially on certain vehicle mirror setups.
Simrad Marine Electronics HALO20 Radar System (24 Nautical Mile Range)
The Simrad HALO20 is a compact 20-inch marine radar dome built for small to mid-size boats that want solid short-to-mid-range awareness without a large, high-draw radar setup. It emphasizes instant-on readiness, pulse-compression clarity, MARPA tracking for up to 10 targets, and preset modes for different operating conditions.
Raymarine Quantum 2 Doppler Radar with 15m Cable (T70417)
Raymarine Quantum 2 Doppler radar with a 15m power and data cable is built for solid-state marine radar performance with features like Doppler collision avoidance, safety sector alerts, MARPA, and target trails. It’s a strong fit if you want Doppler assistance and want the flexibility of either Wi‑Fi or hardwired data connection, but it depends on your existing Raymarine setup for full compatibility.
Furuno DRS4D-NXT Solid-state Doppler Radar, 24 Dome
The Furuno DRS4D-NXT is a compact 24-inch radome solid-state Doppler radar designed to improve situational awareness with pulse compression and Doppler-based “Target Analyzer” color cues. It is aimed at boaters who want simpler installation (including no radome opening and no warm-up time), but buyers should be ready for a learning curve in setup and operation, and they may need compatible display integration.