(Pack of 6) Single AA Battery Holder, 1 X 1.5V AA Battery Holder, AA Battery Holder with Leads Wires
Quick take
This 6-pack single AA battery holder is designed for projects and device repairs where you need an AA battery in a compact form factor plus ready-to-wire lead connections (red for positive, black for negative). Buyers generally report a snug battery fit and practical usability, though some note the lead wires could be thicker depending on your wiring plan.
Pros and cons
Pros
- Includes red and black tinned lead wires (about 5.9 in / 15 cm), helpful for quick wiring.
- Compact holder size, roughly 2.248 in x 0.669 in x 0.539 in (L*W*H) per unit.
- Battery flaps reported as firm, helping keep the AA securely seated.
- Supports DIY series setups to combine holders for higher pack voltages (3V, 4.5V, 6V, up to 9V mentioned).
Cons
- No built-in ON/OFF switch and no cover on the holder.
- Some buyers wish the wire leads were thicker for certain wiring or stress conditions.
What buyers think
Buyer-review evidence is consistent on a few practical points. People describe these as useful for powering projects and for replacing battery holders in small devices, noting the compact size and that the AA battery sits tightly. Several comments also highlight how the wire leads make wiring simpler, including using the holders with connectors like alligator clips. The main limitation mentioned in reviews is wire thickness, but performance and fit are generally described as satisfactory for typical DIY and replacement uses.
What this battery holder is, and where it fits
This is a single AA (1.5V) battery holder with two lead wires already attached, intended for straightforward integration into electronics or repairs. If your project needs a reliable AA connection point that you can route into a small enclosure, this style of holder is a practical building block.
Each pack includes 6 battery holders with leads. The lead wires are red and black, with the red lead contacting the positive side and the black lead contacting the negative side of the battery holder.
Key specs that affect your build
Voltage and DIY series option
One holder is rated for 1.5V with a single AA. The listing also describes a DIY approach to combine multiple holders for higher voltages by joining holders in series, suggesting 3V (two holders), 4.5V (three), 6V (four), and up to 9V (six).
Wires and how long you get
Each holder includes tinned wire ends (useful for soldering or connecting with compatible hardware). Wire length is listed as 5.9 in (15 cm). Cable diameter is about 0.0393 in (1 mm) with PVC insulation, and the wire color is red/black.
Size and weight
Per holder, the approximate dimensions are 2.248 in x 0.669 in x 0.539 in (5.71 cm x 1.70 cm x 1.37 cm). Weight is listed as about 4 g per holder. That combination is typically what you want when space is tight, such as compact lamps, small electronics housings, or clock-style repairs.
Physical design notes
- Plastic ABS case.
- No switch (so you will control power externally if needed).
- No protective cover on the holder itself.
Pros and cons for real buyers
Good fit if you’re doing DIY wiring or small repairs
These are especially convenient when you are replacing a battery holder inside an existing device or building a small circuit where you need AA power brought out as wires. The compact dimensions and ready-to-wire leads make it easier than sourcing a holder and then attaching contacts yourself.
Potential tradeoffs to consider first
- If your wiring requires thicker, stiffer cable for handling or durability, you may find the supplied leads limiting. Some buyers specifically wish the wires were thicker.
- If you expected an integrated on/off switch or a fully enclosed battery cover for safety, this holder does not include those features, so you may need to add them in your enclosure or circuit design.
Is it worth it?
It’s worth considering if you want a budget-friendly set of AA holders with leads for compact projects, quick replacements, or beginner-to-intermediate DIY builds. It’s less ideal if you need a built-in switch, a covered battery compartment, or heavy-duty wiring for applications that put strain on the leads.
Alternatives to consider (by feature priority)
If you need a switch or a covered compartment
Look for AA battery holders that include an on/off switch and/or an enclosure or cover, especially for devices you’ll carry or move often.
If you need thicker wiring
Consider holders with heavier gauge lead wire, or plan to reinforce the connection by adding your own wire extension after using the leads for a simple temporary interface.
If you need fewer than six units
If you only have one device to fix, a single-pack or smaller quantity option may reduce surplus. (The advantage of a 6-pack is that it gives you spares for future projects.)
Verdict
The (Pack of 6) single AA battery holder with red/black leads is a practical choice for compact DIY electronics and battery-holder replacements where you want wire-ready power and a snug battery fit. The biggest reasons to pass are the lack of an ON/OFF switch and the possibility you will want thicker lead wiring depending on your installation.
FAQ
How many battery holders are included?
There are 6 single AA battery holders in the pack, each with leads wires.
What voltage does each holder provide?
Each holder is designed for 1.5V with a single AA battery.
Are the wires already connected to the battery holder?
Yes. Each holder includes red and black tinned lead wires, with red for the positive side and black for the negative side.
Is there an on/off switch or a battery cover?
No. This holder does not include an ON/OFF switch, and it does not have a cover.
How long are the lead wires?
The lead wire length is listed as about 5.9 in (15 cm).
Can multiple holders be combined for higher voltage?
The listing describes a DIY series approach, where joining multiple single AA holders can increase the total voltage (for example, 3V with two, 4.5V with three, and higher up to 9V with six).
View latest price on Amazon
Specifications
| Product Title | (Pack of 6) Single AA Battery Holder, 1 X 1.5V AA Battery Holder, AA Battery Holder with Leads Wires |
|---|---|
| Category | Electronics > Household Batteries, Chargers & Accessories > Battery Holders |
| Manufacturer | LAMPVPATH |
| Item Weight | 0.81 ounces |
| Package Dimensions | 5 x 3.5 x 0.6 inches |
| Item model number | 6543877239 |
| Is Discontinued By Manufacturer | No |
Recommended next
Comecase Battery Organizer Storage Case, Battery Vault Carrying Container Bag review
The Comecase battery organizer storage case is a high-capacity, EVA foam-lined holder designed to keep AA, AAA, C, D, 9V, and button-cell batteries separated and easier to find. A removable BT-168 digital tester is included to quickly check 1.5V and 9V battery power, but it is not meant to replace a charger, and the organizer can be a bit labor-intensive to set up when you first remove the foam pieces.
ENGPOW Battery Organizer, Fireproof Battery Organizer Storage Case with Tester (BT168)
The ENGPOW BT168 is a soft, zipper-closed battery storage case designed to hold 220+ mixed battery types while keeping them separated in foam cutouts. It adds a battery tester for quick “what to recycle” checks and aims to reduce risk with fire-retardant, water-resistant materials. It is best for households that want a single place for AA/AAA/C/D/9V and common button batteries, but it has a fixed slot layout, so niche battery shapes may not fit perfectly.
2 Pack Battery Holder for Milwa.....12V Tool, Wall Mount for review
A two-pack, wall-mountable aluminum battery rack system for organizing 12V tool batteries. Four slots per holder help keep batteries in one place, reduce clutter, and make it faster to grab the right charged pack.
Kalinar Battery Ladder Organizer Case for AA & AAA Batteries (2-Pack, FIFO Dispenser)
The Kalinar AA and AAA battery ladder organizers help you store rechargeable batteries in a first-in, first-out (FIFO) flow. It’s a compact, wall-mountable way to reduce clutter and make it easier to grab the next oldest battery, though stacking and smooth feeding can vary by slot and battery size.