(Pack of 6 CR2032 Battery Holder Coin Cell Holder with Switch, 2 x 3V CR2032 Button Coin Cell Battery Holder with Leads On Off Switch)
Quick take
This 6-pack of CR2032 battery holders is designed for quick wiring, with built-in red and black leads and an on/off switch for each holder. It is best for hobby electronics, small displays, and retro repairs where you want a compact, mountable coin-cell battery connection. The main caveat is that switch behavior can be sensitive to how you physically press or hold the holder during toggling.
Pros and cons
Pros
- Includes an on/off switch, which helps you control power without adding extra circuitry.
- Pre-attached tinned wire leads (red and black) make it easier to connect to your project.
- Compact ABS holder housing with screw mounting, helpful for DIY installations.
- Supports 2 x CR2032 per holder (commonly used for 6V setups), with flexibility for lower-voltage use cases.
Cons
- It is specifically for CR2032 cells, so it is not a universal coin-cell holder.
- Buyer feedback suggests the on/off behavior can be a bit “quirky” if the holder is pressed while switching (important for precise builds).
- Leads are a fixed length, so wiring distance may require splicing or longer runs.
What buyers think
Buyer-review evidence for this holder is limited in size and not every review addresses the same build details, but a few themes show up consistently. People generally describe the holders as easy to install and useful for small DIY or replacement projects. Several buyers highlight the compact, mount-friendly design and find the lead wiring convenient for getting circuits working quickly. There is also mention of the switch and contact behavior being more sensitive than “set-and-forget” in certain hands-on scenarios, especially when the holder is physically manipulated while toggling.
Who this battery holder is for
Choose this CR2032 holder set if you want:
- Compact coin-cell power for small electronics or hobby builds.
- An integrated on/off switch so you can cut power during testing, demo mode, or storage.
- Ready-to-wire leads (tinned ends) to connect to a circuit without crimping or soldering the first connection from scratch.
- A mounting approach that uses screws and a plastic ABS housing.
Key features that affect your build
Switch + wire leads (less wiring work)
Each holder includes an on/off switch and red/black leads with a tinned wire end. That combination is helpful when you are integrating battery power into a project enclosure where you want a single, accessible switch rather than adding a separate inline switch on the wire.
CR2032 form factor, with 2-cell capacity per holder
These holders are made to take CR2032 coin cells, and each holder is intended to accommodate two 3V CR2032 batteries (rated for a 6V output configuration). That flexibility can be useful for projects that may run at different voltage requirements, as long as your circuit wiring matches how you populate the holder.
Dimensions and cable length matter
The holder’s compact body is sized for integration into small spaces. The included lead length is about 5.7 in (14.5 cm), so if your circuit board or connection point is farther away, you may need to plan for extra wire length, splicing, or routing inside your enclosure.
Pros and cons (expanded)
Pros
- More convenient than bare battery clips because the switch is built into the holder.
- DIY-friendly wiring thanks to included red and black leads with tinned ends.
- Good fit for small enclosures due to the compact ABS housing and screw mounting.
- 2 x CR2032 support gives you an easy path to 6V-style setups using the same mechanical footprint.
Cons
- Not universal, it only works with CR2032 coin cells.
- Switch sensitivity may be noticeable in some hands-on use, particularly if the holder is pressed or held during switching.
- Fixed lead length can be limiting for larger layouts unless you add wire.
Price and availability
This product is offered as a pack of 6 holders. If you are buying for multiple projects or need spares, a multi-pack format can be a practical value compared with sourcing individual holders. For the most current pricing and stock status, check the listing before ordering.
Should you buy it? The verdict
Buy it if you need CR2032 battery holders that include both a switch and leads, and you are building or repairing small electronics where you want a tidy, mountable battery connection. Skip it if your project needs a different coin-cell size, you require very consistent switch behavior while physically manipulating the holder, or your wiring distance is significantly longer than the included lead length without additional cable planning.
Alternatives to consider
- CR2032 holders without switches: better if you already have an inline switch or want maximum control over how switching is implemented in your circuit.
- Battery holders with longer leads: a good fit if your enclosure wiring distance is more than the ~14.5 cm lead length.
- Single-cell (one CR2032) holders: consider these if your circuit only needs 3V and you want to avoid managing a dual-cell footprint.
FAQs
What batteries does this holder take?
It is designed for CR2032 coin cells. Each holder is intended for two CR2032 batteries (a common 6V-style configuration).
Does it include an on/off switch?
Yes. The holder includes an integrated on/off switch for controlling power from your project.
Does it come with wires?
Yes. It includes red and black tinned leads for connecting to your circuit. The lead length is about 5.7 in (14.5 cm).
Can I use it for a 3V setup instead of 6V?
The holder is built for two CR2032 cells (rated for 6V when both are used). For 3V-style needs, you may be able to configure your circuit based on how you populate the holder, but your exact wiring should match your device’s power requirements.
Is it easy to mount?
It is intended to mount with screws (included), and the housing is designed to be compact for DIY enclosures.
What’s the best type of project for these holders?
They are a good match for small DIY electronics, compact battery-powered devices, and replacement parts where you want a simple, mountable battery connection with an integrated switch and ready-to-wire leads.
View latest price and details: Buy on Amazon
Specifications
| Product Title | (Pack of 6 CR2032 Battery Holder Coin Cell Holder with Switch, 2 x 3V CR2032 Button Coin Cell Battery Holder with Leads On Off Switch |
|---|---|
| Category | Electronics > Household Batteries, Chargers & Accessories > Battery Holders |
| Brand | LampVPath |
| Manufacturer | LAMPVPATH |
| Model Name | Lampvpath |
| Model Number | 6543877237 |
| Item Weight | 0.08 Pounds |
| Number of Batteries | 6 CR2032 batteries required. |
| UPC | 739340317348 |
| Battery Capacity | 6 Volts |
| Voltage | 6 Volts |
| Reusability | Single Use |
| Unit Count | 6 Count |
| Battery Weight | 6 Grams |
| Item Dimensions | 2.19 x 0.94 x 0.24 inches |
| Antenna Location | Watch |
| Recommended Uses For Product | Watch |
Recommended next
Comecase Battery Organizer Storage Case, Battery Vault Carrying Container Bag review
The Comecase battery organizer storage case is a high-capacity, EVA foam-lined holder designed to keep AA, AAA, C, D, 9V, and button-cell batteries separated and easier to find. A removable BT-168 digital tester is included to quickly check 1.5V and 9V battery power, but it is not meant to replace a charger, and the organizer can be a bit labor-intensive to set up when you first remove the foam pieces.
ENGPOW Battery Organizer, Fireproof Battery Organizer Storage Case with Tester (BT168)
The ENGPOW BT168 is a soft, zipper-closed battery storage case designed to hold 220+ mixed battery types while keeping them separated in foam cutouts. It adds a battery tester for quick “what to recycle” checks and aims to reduce risk with fire-retardant, water-resistant materials. It is best for households that want a single place for AA/AAA/C/D/9V and common button batteries, but it has a fixed slot layout, so niche battery shapes may not fit perfectly.
Battery Organizer Storage Box, Garage Case Holder for 24* AA, 30* AAA Batteries (white)
This ALCYON battery organizer storage box keeps up to 54 AA and AAA batteries separated in pre-cut foam slots for faster, cleaner storage. It has a secure latch lid and a wall-hanging clip option, but buyer feedback suggests it is best for home cabinet use rather than rough transport.
GlossyEnd Set of 4 - Two C and Two D Battery Storage Box (Clear)
The GlossyEnd set includes four clear plastic battery storage boxes, designed specifically for organizing C and D batteries. Snap lids and built-in separation help keep fresh and dead rechargeable batteries apart, but the boxes are not water resistant, so they are best for indoor storage and light travel use.