MokerLink 26 Port Gigabit PoE Switch, 24 Gigabit PoE+ Ports, 2 Gigabit SFP Uplink
Quick take
This 1U, fanless unmanaged PoE+ switch gives you 24 gigabit PoE+ downlinks plus two gigabit SFP uplinks for connecting cameras, access points, and other Ethernet devices. It is built for plug-and-play use with automatic power detection and a total 300W PoE budget, but it will not power passive 24V PoE devices, so device compatibility matters.
Pros and cons
Pros
- 24 gigabit PoE+ ports with a high total PoE power budget (300W) and 802.3af/at support.
- Two gigabit SFP uplinks for flexibility and potentially longer reaches than copper in many setups.
- Fanless, metal 1U rackmount design aimed at quiet operation for home or office racks.
- Extra built-in features for unmanaged operation, including port-based VLAN and an “extend” mode.
Cons
- Unmanaged, so there is no full web interface or granular port/PoE control.
- Extend mode trades speed for distance, dropping to 10Mbps on the specified ports.
- Only powers IEEE 802.3af/at PoE devices, not passive 24V PoE (48V PoE is required).
What buyers think
Buyer-review evidence for this switch is limited to a few recurring themes. Where feedback is available, shoppers commonly describe the switch as easy to set up (plug-and-play) and reliable for powering PoE access points and IP cameras. The two SFP uplinks are also mentioned as useful when linking to another switch or adding flexibility for uplink connections. The fanless design comes up as a practical benefit for rack or office use where quiet operation matters. Some buyers note that unmanaged operation limits configuration depth, and a few report that practical configuration details (like IP behavior) can be non-intuitive for their specific setup, though this aligns with the “no web configuration” expectation for an unmanaged PoE switch.
Key features that matter for day-to-day use
24 PoE+ ports plus two SFP uplinks
With 24 gigabit RJ45 PoE+ ports, this switch is positioned for multi-device deployments like security cameras, wireless access points, and other PoE networking gear. The two gigabit SFP uplinks help you connect upstream over fiber (or using compatible SFP modules) when you need more distance or a cleaner rack-to-rack link.
300W total PoE power, built for mixed loads
The switch includes a built-in power supply and supports IEEE 802.3af/at. It is rated up to 300W total PoE output, and each PoE port is designed for up to 30W when using PoE+ devices. In other words, it is intended for common “real-world” PoE camera and AP combinations without requiring external power bricks.
Plug-and-play power detection (and device safety)
It uses power detection so it should deliver power only when an IEEE 802.3af/at compatible PoE device is present, while still passing network traffic for non-PoE devices. This is handy if your rack includes a mix of PoE and non-PoE equipment, such as PCs or routers.
Unmanaged VLAN and an extend mode (with a speed tradeoff)
Even though it is unmanaged, there are DIP-switch features meant to reduce common network issues in camera deployments. Port-based VLAN can isolate ports 1–24 from each other while still allowing communication through the uplink, which can help limit broadcast or multicast-style effects between camera endpoints. There is also an “extend” mode for ports 17–24 that supports longer runs up to 250 meters, but the maximum speed drops to 10Mbps on those extended links.
Who this switch is best for
- Home and small office camera or AP deployments where you want PoE power and gigabit Ethernet without managing the switch via software.
- Rack users who need quiet operation, since the design is fanless.
- Setups needing SFP uplinks, such as connecting to a core switch over fiber or placing the uplink farther from the PoE switch than copper alone.
- Buyers balancing PoE capacity and port count, since 24 PoE+ ports with a 300W budget covers many typical multi-camera and multi-AP combinations.
Who should avoid it
- You need deep switch management (web UI, advanced monitoring, per-port control). This is unmanaged, so expect limited configurability.
- Your PoE devices are passive 24V PoE (not IEEE 802.3af/at). This switch is for 48V PoE standards and will not power passive 24V gear.
- You cannot accept reduced throughput for long-distance cabling. The extend feature lowers speed to 10Mbps on the supported ports.
Pros and cons in plain language
Pros: If your priority is a straightforward, quiet, rack-friendly PoE+ switch for cameras and access points, the combination of 24 PoE+ ports, 300W total budget, and two SFP uplinks is a strong fit. The inclusion of VLAN and an extend mode also adds useful capability without requiring management software.
Cons: You will give up advanced control because the switch is unmanaged. Also, your long-run cabling plan needs to account for the speed reduction when using extend mode, and your PoE devices must match IEEE 802.3af/at.
Comparison checklist (so you buy the right kind)
- Managed vs. unmanaged: Choose unmanaged if you want plug-and-play, basic isolation features, and you do not need per-port configuration via web UI.
- PoE standard compatibility: Confirm your cameras/APs are IEEE 802.3af/at (PoE or PoE+). If they are passive 24V PoE, look for a different switch or use a splitter, if appropriate for your device.
- Uplinks you need: If you prefer fiber for uplinks, the two gigabit SFP ports are a practical differentiator versus switches that only have copper uplinks.
- Distance requirements: If you truly need up to 250 meters, plan for extend-mode 10Mbps, not full gigabit.
Bottom line verdict
The MokerLink 26 Port Gigabit PoE Switch is a solid choice for buyers who want a fanless, 1U unmanaged PoE+ switch with plenty of gigabit PoE ports and SFP uplinks. It is especially well-suited to typical camera and access point setups where plug-and-play simplicity is the main goal. Just make sure your devices are IEEE 802.3af/at PoE+ (not passive 24V) and that you can accept the throughput reduction when using the long-run extend mode.
FAQs
Is this a managed or unmanaged PoE switch?
It is an unmanaged switch, so it is designed for plug-and-play operation without a web interface for configuring ports or PoE behavior.
Does it support PoE+ and how much power is available?
Yes, it supports IEEE 802.3af/at. The switch is rated for up to 300W total PoE output, with up to 30W per PoE port for PoE+ devices.
What devices will it power, and will it work with passive 24V PoE?
It is intended for IEEE 802.3af/at (48V) PoE devices. It will not supply power to passive 24V PoE devices; however, it can still pass network data to non-PoE equipment.
How do the SFP uplinks work?
It includes two gigabit SFP uplinks, which are meant for fiber-based uplinks to connect to routers, switches, servers, or other network segments beyond typical copper limitations.
What is the extend mode and what speed should I expect?
When extend mode is enabled for ports 17–24, it can increase distance up to about 250 meters, but the maximum speed drops to 10Mbps on those extended links.
Specifications
| Product Title | MokerLink 26 Port Gigabit PoE Switch, 24 Gigabit PoE+ Ports, 2 Gigabit SFP Uplink, 300W IEEE802.3af/at, Fanless Rackmount Unmanaged Plug and Play Ethernet Switch |
|---|---|
| Category | Electronics > Computers & Accessories > Networking Products > Hubs |
| Brand | MokerLink |
| Manufacturer | MokerLink |
| Model Number | 24 Gigabit PoE + 2SFP |
| Item Weight | 3.4 Kilograms |
| Color | Black |
| Number of Ports | 26 |
| Compatible Devices | Desktop |
| Voltage | 48 Volts |
| Maximum Power | 300 Watts |
| Interface | PoE, SFP |
| Data Transfer Rate | 1000 Megabits Per Second |
| Switch Type | Metal |
| Platform | No Operating System |
| Case Material Type | Metal |
| Built-In Media | MokerLink Switch, Power Cord, Quick Installation Manual, Rackmount Kit |
| Mfr Part Number | POE-G242GS |
| Included Components | MokerLink Switch, Power Cord, Quick Installation Manual, Rackmount Kit |
Available variants
Number Of Ports
- 8
- 10
- 6
- 26
- 5
- 9
- 28
Recommended next
![SABRENT 4 Port USB 2.0 Data Hub with Individual LED lit Power Switches [Charging NOT Supported] for Mac & PC (HB-UMLS)](/product-images/019ed146-ec71-7f8b-9f8c-2c744a294dd1-0-d595b4582e23.webp)
SABRENT 4 Port USB 2.0 Data Hub with Individual LED lit Power Switches [Charging NOT Supported] for Mac & PC (HB-UMLS)
The SABRENT HB-UMLS adds four USB 2.0 ports with individual on/off switches and per-port LED power indicators. It is a plug-and-play, hot-swappable hub for simple peripherals like mice, keyboards, and flash drives, but it does not support charging (and powered USB storage may need external power).
TOTU 11-in-1 USB-C Hub: 4K HDMI, VGA, 2x USB3.0, 2x USB2.0, Ethernet, SD Card Reader, Audio, 3.0 PD, Mac Pro & Laptops Compatible
The TOTU 11-in-1 USB-C hub is a compact all-in-one dock that adds HDMI and VGA video, gigabit Ethernet, dual card slots, audio, and multiple USB ports, plus USB-C PD pass-through charging up to 87W. It’s a strong fit for travelers and laptop owners who want one adapter for monitors, wired internet, and everyday accessories, with the main caveat that dual HDMI+VGA output duplicates rather than extends.
Cable Matters Ultra Mini 4 Port USB Hub (USB 3.0 Hub, USB3 Dock)
The Cable Matters Ultra Mini 4-Port USB Hub turns one USB 3.0 port into four, using a compact, travel-friendly design with a 5 Gbps data rate and bus-powered operation (no bulky adapter). It is a strong choice for adding a mouse, keyboard, receiver, or storage, but it is not a charger and performance depends on what you plug in, including limitations with high-power USB storage setups.
Legrand - OnQ Cat 6 Network Interface Module (AC1068)
The Legrand On-Q AC1068 is an 8-port Cat 6 network interface module designed to snap into On-Q structured wiring enclosures. It uses front-mounted 110-IDC punchdown terminals plus RJ45 jacks for a clean, patch-panel-like home networking setup, with strong buyer feedback on fit and installation. The main caveat is termination format, some buyers note T568A vs T568B awareness during wiring.