Delamu 236in Cord Hider, Single-Wire Cord Covers for Wires on Wall
Quick take
This Delamu kit is a one-wire cable raceway system that snaps shut over a single low-voltage cable and guides it around corners with included elbows and connectors. It is a good fit for tidying up wall-mounted lamps, sconces, media setups, and cable runs where you want a paintable, low-profile look.
The main caveat is sizing and routing: this channel is meant for a single cord (and it is not intended for concealing two thicker network cables at the same time).
Pros and cons
Pros
- Snap-on, tool-free install with double-sided tape (no drilling required).
- Paintable white PVC raceway helps it blend with walls and trim.
- Includes corner-focused pieces (connectors plus flat, inner, and outer elbows) for cleaner routing.
- Designed specifically for one-cord hiding (useful for lamp cords, speaker wire, phone/fax lines, and one Ethernet cable).
Cons
- Not a bundle-cable solution, the channel is sized for one wire and similar profiles.
- Adhesive placement matters, the tape is described as very strong, so plan the run before committing.
- Buyer feedback suggests it may not suit every wall type, for example textured surfaces.
- Some installs may require careful planning around connectors, and straight splice use can affect the finished look.
What buyers think
Buyer-review evidence is generally consistent around ease of use and appearance. Many people describe the installation as straightforward and fast, especially when they take time to measure, keep the run straight, and dry-fit pieces before applying tape. Several comments highlight that the raceway looks neater once covered, and that painting can help it disappear against the wall.
There are also a few practical themes about fit and routing. Reviews often mention that this is well-suited for a single, fairly thick cord (for example, speaker or similar cable profiles), while thinner cables may allow more than one cord to fit. The included corner parts are helpful for managing bends, but some buyers note that planning the layout and deciding where to use connectors matters for the cleanest result. Adhesion and wall texture come up as a deciding factor, with strong tape performance on clean surfaces and uncertainty on textured walls.
How the Delamu one-cord channel works
This is a one-cable raceway kit built around a snap-on cover over a base channel. The kit is made from PVC and comes in white. Installation is tape-based (double-sided tape), which makes it appealing if you want a cleaner look without drilling or wall anchoring.
Because it is a single-wire design, it is most practical when you have one main cord to hide, then use the elbows and connectors to follow the layout around corners or entry points.
Key specs that affect buying fit
- Run length: 236 inches total (15.7-inch channel sections).
- Channel size: about 0.59 inches wide and 0.4 inches high (low-profile raceway).
- Materials: PVC enclosure/base.
- Installation type: double-sided tape.
- Included parts: 15 cable hiding channels, 10 connectors, 5 flat elbows, 2 inner elbows, 2 outer elbows, and 2 rolls of tape (plus guidance to match corner layouts).
Best for (and who should buy)
- Wall-mounted lighting and décor: If you are trying to make sconces, lamps, or similar fixtures look finished, the low-profile, paintable cover can help.
- Single-cord cable management: Use cases commonly include speaker wire, lamp cords, phone/fax wiring, and a single Ethernet cable or similarly sized low-voltage cable.
- Corner routing: The kit is structured around bypassing wall corners and changes in direction using included elbows and connectors.
- DIY-friendly installs: Tape-based mounting is a strong option for renters or anyone who wants to avoid drilling.
Who should avoid it
- If you need to hide multiple thick cables in the same channel, this one-cord format may be limiting.
- If your wall surface is textured and you cannot achieve a clean, tape-friendly mounting area, adhesion may be less predictable.
- If your cable is outside the intended profile, you may need a larger raceway or a different category solution designed for bulkier bundles.
Installation tips buyers consistently mention
- Measure and mark a straight line first: A level helps keep the run visually aligned.
- Dry-fit before taping: Plan where sections meet, especially at the inside and outside corners.
- Plan tape placement carefully: The included adhesive is described as extremely strong, so take time to position correctly before pressing.
- Don’t assume all joining methods look the same: Some buyers suggest avoiding certain straight splices for a more polished finish.
Paintable finish: does it help?
The raceway surface is designed to be paintable, which is the main reason this style of cord cover can look “built-in.” If you are matching it to walls, baseboards, or furniture, painting can make a noticeable difference compared with leaving it purely white.
If you want the cleanest blend, plan for a consistent finish across the visible sections, and consider letting paint dry fully before final handling.
Outdoor and semi-outdoor use considerations
The kit is positioned as suitable for covered outdoor areas such as patios, porches, and covered entryways. For open, unprotected locations exposed directly to wind and rain, it is not recommended. If you plan to use it outdoors, it is wise to consider local weather conditions, because heat and rain exposure can accelerate oxidation of the cable sleeves.
Verdict
The Delamu 236-inch single-wire cord hider is a practical, beginner-friendly cable raceway kit for hiding one cord cleanly, including around corners. It is best when you have a single, low-voltage cable run and a wall surface that will support strong tape adhesion. If you need to conceal multiple thick cables in one channel or your mounting surface is textured, you may want to look for a different size or cable-management approach.
View latest price on Amazon
FAQs
How many cords can this cable hider hold?
It is designed for a single cord (one-cord channel). It can also fit a second cord only when the cables are non-grounded and similarly sized, while thicker combinations may not work as intended.
Does it require drilling?
No. It installs with double-sided tape and a snap-on cover, so you avoid drilling and tools for mounting.
Can I paint the cord hider to match my wall?
Yes. The surface is described as smooth and paintable, so you can match it to your wall tones and trim.
Will it work on textured walls?
Adhesion can be less predictable on textured surfaces. If you have a textured wall, it is important to confirm you can achieve strong contact for the tape before committing to the full run.
What types of cables is it meant for?
It is intended for hiding low-voltage or similar profile cables such as phone/fax wiring, speaker wire, lamp cords, and one Ethernet cable, depending on the cable size.
Specifications
| Product Title | Delamu 236in Cord Hider, Single-Wire Cord Covers for Wires on Wall, Paintable Snap-on Design Wire Cover, Cable Management Kit for Corner-Mounted TVs, Easy Install Cable Raceways, W0.59 H0.4in, White |
|---|---|
| Category | Electronics > Accessories & Supplies > Cord Management > Cable Raceways |
| Brand | Delamu |
| Manufacturer | Delamu |
| Model Number | CC03-9 |
| Color | White |
| Material | Polyvinyl Chloride |
| Product Dimensions | 15.7"L x 0.59"W |
| Number of Pieces | 1 |
| Mfr Part Number | CC03-9 |
| Warranty Description | No |
| Enclosure Material | Polyvinyl Chloride |
| Item Dimensions L x W | 15.7"L x 0.59"W |
| Installation Type | Double-sided Tape |
| Style Name | One-Cord Cord Hider |
| Style | One-Cord Cord Hider |
Available variants
Size
- 142in L X 0.59in W X 0.40in H
- 236in L X 0.59in W X 0.40in H
Color
- Beige
- White
- Black
Recommended next
Legrand Wiremold Cable Management Kit, CordMate II, Cord Organizer and Hider, Cord Cover, Concealer, and Protector for Wall, Medium Capacity, CMK50
The Legrand Wiremold CMK50 CordMate II kit is a self-adhesive cord cover system designed to hide multiple low-voltage and AV cables along walls and around entertainment setups. Buyers like how clean the finished look is and how easy it is to cut and install, with the main tradeoff being adhesive removal risk (paint can lift) and the need to plan placement for level, secure bonding.
No-Screw Under Desk Cable Management Tray - Self-Adhesive Installation, Cord Management, Cable Tray, Under Desk Wire Organizer - White Set of 2
A self-adhesive under-desk cable tray set designed to reduce visible cord clutter and keep power bricks and adapters organized. Buyers like the screwless installation and sturdy, solid feel, with the main tradeoff being that repositioning after the adhesive sets requires care and desk-surface prep matters.
ECHOGEAR TV Cord Hider for Wall Mounted TV (White)
The ECHOGEAR TV cord hider is a DIY cable pass-through kit that lets you route low-voltage A/V cables behind drywall for a cleaner wall-mounted setup. It includes two pass-through grommets, locking brackets, and a hole-saw drill attachment for cutting tidy grommet holes, with a paintable finish to help the openings blend in.
EVEO Cable Hider Wall - 153" Wall Cord Hider (White)
The EVEO Cable Hider Wall is a self-adhesive cable raceway designed to conceal messy cords along baseboards, desks, or behind a wall-mounted TV. It’s cuttable, paintable, and uses a snap-on cover, making it a practical way to improve both the look and day-to-day safety of exposed cables, with the main tradeoff being how strongly the adhesive bonds to the wall.