95mm Adhesive Dashboard Pad Mounting Disk with Adhesive for Suction (2-Pack)
Quick take
This 95mm adhesive dashboard mounting disk is meant to help suction-cup phone holders and Garmin suction mounts stick more reliably to the dashboard, especially when the original surface is textured or not very flat. It creates a smoother, flatter mounting point using a foam adhesive system, but the pads are designed for one-time use after removal, so placement matters.
Pros and cons
Pros
- Designed to work with suction-cup mount bases under 95mm diameter for dashboard mounting flexibility.
- Uses a foam adhesive approach intended to handle textured dash surfaces by improving the contact area for suction.
- Includes installation materials such as a cleaning cloth and user guide.
- Installation is straightforward: clean, apply, press, wait, then attach the suction mount.
Cons
- Once you remove a disk, it is intended to be one-time use, so you should plan your placement.
- Best results require a clean and adequately smooth setup, since the adhesive needs good surface contact.
- The maximum rated hold is listed as 0.05 kg, so it is not meant for heavy accessories.
What buyers think
Buyer-review evidence is limited, but the recurring themes are encouraging. Several reviews describe the adhesive disk as solving a dashboard-mounting problem where suction phone holders or similar setups would detach during driving. Others mention strong attachment and ongoing stability after installation. A smaller portion of feedback focuses on practical installation challenges on uneven dashboards, suggesting buyers may need to carefully evaluate whether their dash surface is appropriate for the adhesive approach.
What this mounting disk actually does
This is a round adhesive pad that you stick to your dashboard, then attach a suction-cup mount base on top. The intent is to turn a dashboard surface that may not work well for suction directly (like textured or less-flat areas) into a flatter, more consistent surface where the suction cup can seat properly.
Key specs that affect compatibility
- Diameter: 95mm (about 3.74 inches).
- Mounting type: dashboard.
- Compatibility: works with any suction cup mount base with diameter less than 95mm.
- Included in the box: adhesive mounting disks (2 count), cleaning cloth, and a user manual/installation guide.
- Materials: plastic enclosure, adhesive + foam layer.
- Maximum listed weight capacity: 0.05 kg.
How to install it for the best chance of staying put
- Clean the dashboard thoroughly and remove dust or debris.
- Remove the protective cover from the base of the disk.
- Press the disk firmly to the dashboard and leave it for more than 30 seconds.
- Attach your suction mount to the center of the adhesive disk.
If your dash is especially uneven, curved, or coated in a way that makes firm contact difficult, you may need to reconsider whether this approach is the right fit.
Pros and cons for real-world use
When it’s a good fit
- You use a suction-cup phone mount or Garmin suction GPS mount and want a more dependable dashboard setup.
- Your dashboard surface is textured or you have had suction cups slip or lose hold over time.
- You want a way to move the mount point (for example, repositioning from windshield to dashboard) while keeping the mount system consistent.
When you may want to skip it
- You anticipate frequent repositioning. Since each adhesive disk is intended for one-time use after removal, it’s better suited for a “pick your spot and commit” installation.
- You need to carry heavy loads. The listed maximum capacity (0.05 kg) is a reminder that this is intended for typical phone/GPS-sized accessories.
- You’re mounting on a surface that cannot be cleaned well or cannot make full adhesive contact.
Is it worth it?
It’s worth considering if your main problem is that suction mounts have been unreliable on your dashboard, especially when the dash surface is not perfectly smooth. The adhesive disk is a practical solution because it changes the contact surface your suction cup relies on. If you need a mount you can reposition often, or you’re working with a dash surface that is difficult to prep cleanly and evenly, the one-time-use adhesive tradeoff may outweigh the benefits.
FAQs
Will this work with my suction-cup phone or Garmin mount?
It’s designed for suction cup mount bases with a diameter less than 95mm. If your mount’s suction pedestal fits within that size range, it should be compatible.
How do I install the adhesive disk?
Clean the dashboard, remove the protective cover on the disk, press it to the surface and wait more than 30 seconds, then attach the suction mount to the center of the disk. A cleaning cloth and guide are included.
Can I remove it and reapply it later?
The disks are intended to be one-time use only. Once removed, they may not be reapplied.
What’s the maximum weight it can hold?
The maximum listed weight capacity is 0.05 kg, so it’s intended for typical phone or GPS mount loads, not heavy accessories.
What surfaces does it work best on?
It’s designed to help when suction cups struggle on textured or less-flat dashboard surfaces by providing a smoother landing area. Clean, properly prepped surfaces generally give the best results.
Specifications
| Product Title | 95mm Adhesive Dashboard Pad Mounting Disk with Adhesive for Suction Cup Phone Mount & for Garmin GPS Suction Mount | 3.74" Wide Diameter 2 Pcs |
|---|---|
| Category | Electronics > GPS, Finders & Accessories > GPS System Accessories > Vehicle Mounts |
| Brand | Randconcept |
| Manufacturer | Randconcept |
| Model Name | Suction Cup Base |
| Model Number | Suction Cup Base |
| Item Weight | 1.8 ounces |
| Compatible Devices | Any suction cup mount base wih diameter less than 95mm |
| Compatible Phone Models | Universal |
| Mounting Type | Dashboard |
| Additional Features | Adhesive, Hand Free, Lightweight, Non-Slip |
| Weight Capacity Maximum | 0.05 Kilograms |
| Water Resistance Level | Water Resistant |
| Compatible with Vehicle Type | Automobile |
| Item Dimensions | 3.5 x 3.5 x 0.3 inches |
| Unit Count | 2 Count |
| Enclosure Material | Plastic |
| UPC | 721248798404 |
| Built-In Media | Adhesive Mounting Disk, Clearing Cloth, User manual |
| Shape | Round |
| Special Feature | Adhesive, Hand Free, Lightweight, Non-Slip |
Available variants
Size
- 70mm
- 95mm
- 80mm
Recommended next
Garmin 010-10908-02 Portable Friction Mount
The Garmin 010-10908-02 is a portable dash friction mount designed to hold compatible Garmin nüvi and StreetPilot devices securely on stable surfaces. It focuses on quick in-and-out mounting, adjustable viewing angles, and a grip-on-dash approach that avoids common windshield suction issues.
RAM MOUNTS B Size 1" Double Socket Mount Arm – Medium Composite (RAP-B-201U)
The RAM-B-201U is a medium-length RAM double-socket arm for B size (1-inch) ball-and-socket systems. It gives you flexible positioning with “near-infinite” angle adjustment and quick pivot setup using a spring inside the arm. Best for riders and vehicle setups that need a compact arm length and strong, marine-grade composite construction, with the main caveat that you must build the rest of your mount with compatible B size components.
Bracketron NavMat Portable GPS Dash Pad Converts Windshield GPS Mount
The Bracketron NavMat is a portable, weighted friction dash pad that lets you turn a windshield-style suction mount into a dashboard mount. It’s a good fit for drivers who want a stable, non-slip base on textured dashboards and want something easy to move between vehicles, with the tradeoff that it is not water-resistant and won’t suit everyone’s dashboard surface.
RAM Mounts Medium Double Socket Arm for B Size 1″ Ball Mount Components (RAM-B-201U)
The RAM-B-201U is a medium-length double socket arm built for RAM’s B-size (1-inch) ball-and-socket mounting ecosystem. It’s made from marine-grade aluminum for demanding environments, offers near-infinite positioning via adjustable sockets, and is rated for up to 2 lb for standard use. The main caveat is that it is a specific “arm” component, so it only makes sense if you already have (or plan to buy) compatible B-size RAM bases and holders.