1Zero GPS Suction Cup Mount for Garmin [Quick Extension Arm]
Quick take
This 1Zero suction cup GPS mount is built to replace a Garmin windshield or dashboard mount that uses a 17 mm swivel ball pattern. It emphasizes easy, one-hand extension (4.13 to 5.75 inches) and wide adjustability (up to a 240-degree pivot) to set an ideal view. The main buying caveat is compatibility, plus that it is mount-only (it does not include the cradle, bracket, or socket parts).
Pros and cons
Pros
- Quick-extension arm adjusts one-handed, from about 4.13 to 5.75 inches.
- Wide positioning options with a 240-degree pivot and rotatable/tilt head design.
- Gel-based suction cup aims to stay in place for heavier Garmin units.
- Made for Garmin models that use a standard 17 mm swivel ball mounting pattern.
Cons
- Not compatible with several listed Garmin models, including some DriveSmart and RV lines.
- Mount-only bundle, no cradle or socket parts included.
- Suction attachment may be difficult to remove and may not be a “swap between vehicles” type of setup.
- Not water resistant.
What buyers think
Buyer-review evidence points to a clear theme: the suction mount is generally reported as staying put even with heavier Garmin setups, and many users describe it as solid and dependable after installation. Several mentions also highlight that the suction cup includes a gel layer designed for stronger hold. There is limited evidence on long-term removal frequency, but at least some feedback suggests the adhesive gel can be very tenacious, so moving the mount repeatedly may be less practical. A smaller number of comments note the ball socket connection can feel a bit tricky (setup feel rather than a recurring failure mode).
Who this mount is for
This mount is a good fit if you want a replacement suction-cup style holder for a compatible Garmin GPS, specifically one that uses a 17 mm swivel ball mounting pattern. It is also well matched to drivers who prefer quick, tool-free adjustments, since the arm length changes with one hand (no screws) and the head can be aimed for better viewing angles.
Key features that affect day-to-day use
One-hand extension for better sightlines
The telescopic arm extends from roughly 4.13 inches to 5.75 inches, with the design intended for quick changes by pushing or pulling. The goal is to help you position the GPS screen for the most comfortable angle without stopping to loosen hardware.
Adjustable head movement
Positioning is supported by a 240-degree pivot and a rotatable, tilt-style head. That combination matters if you route the mount so it sits higher or farther forward on the windshield, or if you need to adjust for different driver heights.
Suction cup with gel base
The mount uses a strong suction cup with an adhesive gel base, designed to hold the mount steadily. In buyer feedback, this is where it seems to shine, including mentions that it held firm with heavier Garmin units and did not pull off during testing of movement and adjustment.
Compatibility and important “do not buy” checks
This is not a universal Garmin mount. It is designed for Garmin GPS units that use a 17 mm swivel ball pattern, and it explicitly will not work with 22 mm or 25 mm ball sockets. It is also specifically not compatible with several listed models, including (examples from the compatibility exclusions) Drivesmart 86, Dezl OTR800/OTR810/OTR1000/OTR1010, RV 890/1090/1095, Overlander, aera 660/760, and certain dash cam series. If your Garmin model or ball size differs, the mount is a mismatch.
Pros and cons (expanded)
What you’ll likely like
- Easy reach adjustments: One-hand arm length changes are meant to make real-world viewing tweaks faster.
- Flexible aiming: The head movement supports dialing in tilt and angle for comfort.
- Stays attached in use: Reviews frequently describe the suction/gel hold as strong.
- Good value as a replacement: It is positioned as an alternative to older mount types like vent, dash pad, or friction mounts when you want a ball-based suction solution.
Tradeoffs to consider
- Removal and re-attachment may be inconvenient: If you plan to swap the mount between multiple vehicles often, suction mounts with adhesive gel can be less suited for repeated repositioning.
- Connection feel at the ball socket: Some feedback mentions the ball socket connection can be a bit tricky, so expect to spend a minute getting the seated fit right.
- Mount-only purchase: The package contents include the suction cup GPS mount and a sticky dashboard pad, not the cradle, mounting bracket, or socket parts.
- Environment expectations: It is not listed as water resistant, so treat it like standard indoor electronics accessories and avoid exposing it to soaking conditions.
Price and availability
This listing typically sits in an entry-level price range for vehicle mount replacements, with the value coming from the adjustable arm and suction hold. Availability can change, so check the current listing for the latest price and bundle options.
Alternatives to consider (by use case)
If you are choosing between mount styles, the right alternative depends on what you want to optimize:
- If you need dashboard or windshield placement but want easy repositioning: consider non-adhesive mounting styles (for example, friction-based pads or vent mounts) if your Garmin setup allows it.
- If you travel between vehicles frequently: look for mounts designed to be re-used more easily without strong adhesive gel behavior.
- If your GPS uses a different ball socket size: switch to a mount explicitly matched to your ball size rather than trying to force compatibility.
Verdict
The 1Zero GPS suction cup mount with quick-extension arm is a practical replacement for compatible Garmin units that use a 17 mm swivel ball mounting pattern. It is designed around one-hand adjustability and a gel suction base that buyers commonly report as holding firmly, which is especially useful if you want stable positioning. Just verify your Garmin model and ball size first, and note that it’s mount-only, so you’ll need to ensure you already have the correct cradle/socket parts for your setup.
FAQ
Is this suction mount compatible with all Garmin GPS models?
No. It is built for Garmin GPS units that use a 17 mm swivel ball mounting pattern and will not fit 22 mm or 25 mm ball sockets. It is also listed as incompatible with several specific Garmin models (including certain DriveSmart, Dezl OTR, RV, Overlander, and aera models).
Does it include the cradle or socket part for my Garmin?
No. The package includes the suction cup GPS mount, a sticky dashboard pad, and an installation guide, but not the mounting bracket, cradle, or socket parts.
How far does the arm extend, and can you adjust it one-handed?
Yes. The telescopic arm adjusts from about 4.13 inches to 5.75 inches using one-hand push or pull movement.
Will the suction cup hold on a heavy Garmin unit?
Buyer feedback suggests it can hold steady even with heavier Garmin setups. Some users also describe the gel layer as very strong, which can make removal difficult.
Is it intended for windshield or dashboard use?
Both. The mount is described as suitable for windshield and dashboard placement, and it includes a sticky dashboard pad for options beyond the suction cup.
Specifications
| Product Title | 1Zero GPS Suction Cup Mount for Garmin [Quick Extension Arm], Replacement GPS Dash Ball Mount Dashboard Windshield Car Holder for Garmin Nuvi Dezl Drive Drivesmart Zumo Driveassist DriveLuxe RV |
|---|---|
| Category | Electronics > GPS, Finders & Accessories > GPS System Accessories > Vehicle Mounts |
| Brand | 1Zero |
| Manufacturer | Epeius International Inc Limited |
| Model Name | EP-S02 |
| Model Number | EP-S02 |
| Color | 1-Pack |
| Item Weight | 4.8 ounces |
| Compatible Devices | Garmin GPS |
| Compatible Phone Models | Garmin Nuvi 1100 1200 1250 1260 1300 1350 1370 1390 1450 1490 1690 (LM LMT T), 2200 2250 2300 2350 2360 2370 2450 2455 2457 2460 2475 2495 2497 2539 2555 2557 2558 2559 2577 2589 2595 2597 2598 2599 2639 2689 2699 (LM LMT LT), 3450 3490 3550 3590 3597 3750 3760 3790 5000 (LM LMT), 30 40 42 44 50 51 52 54 55 56 57 58 60 61 65 67 68 (LM LMT), 200 205 250 255 260 265 270 275 285 295 350 360 370 465 500 550 600 610 650 660 670 680 750 755 760 765 770 775 780 785 850 855 880 885 (W WT T LMT), etc |
| Mounting Type | Windshield, Dashboard |
| Additional Features | Adjustable, Hand Free, One-Hand Operation, Rotatable, Tilt Head |
| Water Resistance Level | Not Water Resistant |
| Compatible with Vehicle Type | Automobile, Truck |
| Unit Count | 1 Count |
| Arm Length | 5.75 Inches |
| Shape | Rectangular |
| UPC | 615150780223 |
| Mfr Part Number | 6654512211 |
| Warranty Description | 1Zero 2 Year Manufacturer |
| Built-In Media | 1Zero GPS Suction Cup Mount for Garmin |
| Enclosure Material | Acrylonitrile Butadiene Styrene |
Available variants
Color
- 2-Pack
- 1-Pack
Recommended next
Garmin 010-10908-02 Portable Friction Mount
The Garmin 010-10908-02 is a portable dash friction mount designed to hold compatible Garmin nüvi and StreetPilot devices securely on stable surfaces. It focuses on quick in-and-out mounting, adjustable viewing angles, and a grip-on-dash approach that avoids common windshield suction issues.
Miracase Phone Holders for Your Car with Metal Hook Clip, Air Vent Cell Phone Stand Car Mount, Dark Black
The Miracase air-vent phone mount uses a metal hook and clamp arms to hold phones securely while you drive. It’s designed for most phones from 4.0 to 7.2 inches (including thicker cases) and supports 360-degree rotation for portrait or landscape viewing. The main caveat is compatibility: it fits horizontal and vertical air vents (not round vents), and the vent blade width needs to be under about 1.4 inches.
RAM MOUNTS Diamond Ball Base with 2-Hole AMPS Pattern, B Size 1" Ball Mount (RAM-B-238U)
The RAM-B-238U is a RAM Mounts B-size (1-inch ball) diamond plate base with a 2-hole AMPS pattern, designed to bolt into a vehicle or gear setup and then connect to any compatible RAM ball-and-socket system. It is made from powder-coated, marine-grade aluminum and uses RAM’s adjustable ball-and-socket connection for flexible positioning. The main caveat is fitment: you will need to pair it with the right RAM device holder/cradle and confirm your AMPS spacing matches.
RAM MOUNTS Tough-Claw Small Clamp Mount Base – B Size 1" Ball, Fits 0.625"-1.14" Rails (RAP-B-400U)
The RAM MOUNTS Tough-Claw Small Clamp Mount Base (RAP-B-400U) is a compact clamp-on mounting base built for odd-shaped rails and bars. It’s designed to quickly attach to rails in the 0.625" to 1.14" range and pair with RAM 1" B-size ball components, making it a strong fit for phones, tablets, action cameras, and rod-holder style setups. The main tradeoff to consider is that the clamp can take a bit of effort to open wide enough on larger-diameter tubes.